Пример настройки моей ноды BPQ32 US1GHQ-5

; Basic Webmail configuration

;SIMPLE ; This set a whole load of paramters to reasonable defaults

LOCATOR=KN95LA ; Set to your Grid Square to send reports to the BPQ32 Node Map system
MAPCOMMENT=LinBPQ TEST NODE

SAVEMH=1 ; записывает в пам¤ть список, кого слышно на радио порте!

NODECALL=US1GHQ-5
BBSCALL=US1GHQ-8

;NODEALIAS=US1GHQ
; в алиас записываетс¤ не позывной, а какое-нибудь слово не более 6 букв
; обычно от названи¤ города...

NODEALIAS=NODKHE
BBSALIAS=BBSKHE

INFOMSG:
US1GHQ's LinBPQ Gateway
***

IDMSG:
US1GHQ-5 KHERSON BBS US1GHQ-8
***

CTEXT:
Welcome to US1GHQ BBS
Type ? for list of available commands.
***
FULL_CTEXT=1        ; 0=send CTEXT to L2 connects to NODEALIAS only ; 1=send CTEXT to all connectees

;For EasyTERM
;AGWPORT=9001
;AGWMASK=0x30
;AGWSESSIONS=10

;Misc Settings

AUTOSAVE=1
BBS=1
NODE=1
HIDENODES=0         ; If set to 1, nodes beginning with a # ; require a 'N *' command to be displayed.
ENABLE_LINKED=N     ; Controls processing of *** LINKED command
                    ; Y = allows unrestricted use
                    ; A = allows use by application program
                    ; N = disabled

;-----------------------------------------------  NETWORK SYSTEM PARAMETERS ----------------------------------------
OBSINIT=6           ; Initial obsolescence set when a node is included ; in a received nodes broadcast. This value is then ; decremented by 1 every NODESINTERVAL.
OBSMIN=4            ; When the obsolescence of a node falls below this ; value that node`s information is not included in ; a subsequent nodes broadcast.
L3TIMETOLIVE=25     ; Max L3 hops
L4RETRIES=3         ; Level 4 retry count
L4TIMEOUT=60        ; Level 4 timeout in seconds s/b > FRACK x RETRIES
L4DELAY=2           ; Level 4 delayed ack timer in seconds
L4WINDOW=4          ; Level 4 window size
BUFFERS=4096        ; Buffer Size
NODESINTERVAL=25    ; Nodes broadcast interval in minutes
IDINTERVAL=0        ; 'IDMSG' UI broadcast interval in minutes, 0=OFF
BTINTERVAL=0        ; The BTEXT broadcast interval in minutes, 0=OFF
MAXLINKS=126        ; Max level 2 links
MAXNODES=1256       ; Max nodes in nodes table
MAXROUTES=128       ; Max adjacent nodes
MAXCIRCUITS=128     ; Max L4 circuits
MINQUAL=83          ; Minimum quality to add to nodes table
PACLEN=236          ; Max packet size (236 max for net/rom)
T3=180              ; Link validation timer in seconds
IDLETIME=900        ; Idle link shutdown timer in seconds
;NODEMAPSERVER=127.0.0.1
;CHATMAPSERVER=127.0.0.1

APRSDIGI
APRSCall US1GHQ-1
StatusMsg=|LoRa_APRS 433.775MHz|AFSK_APRS 144.800MHz|IGATE|http://aprs-adugeya.ru/
Symbol=&        ; Icon to display for station. Default is House if omitted
Symset=L
;
;    Specify a Dest and Path for each port you want to use for APRS. No dest means receive only port
;	  Ports without an APRSPath statement will not be used by the Digi
;
APRSPath 3=APRS,WIDE2-1
APRSPath 4=APRS,WIDE2-1
APRSPath 5=APRS,WIDE2-1

BeaconInterval=10      ; Send Beacon every 30 minute
DISTKM=1
MAXAGE=1440

;    Define Crossport Digi. For each port, a list of ports to send a packet to (IS means send to APRS-IS)
;    If a Digimap isn`t specified for a port, digi out on the port the packet arrived on,
;	  	  and send to APRS-IS (if enabled)
;    If you want to digi on same port, but not send to APRS-IS, Specify Digimap n=n 
;Digimap 5=5,16,       ; Packets from 5 to 16, but not APRS-IS
Digimap 3=3,IS,
Digimap 4=4,IS,
Digimap 5=5,IS,

TraceCalls=WIDE,TRACE  ; Calls for CALLN-n Processing with Trace
;;TraceCalls=WIDE,IN    ; Calls for CALLN-n Processing with Trace
FloodCalls=LYA         ; Calls for CALLN-n Processing without Trace
DigiCalls=US1GHQ       ; Calls for Normal (ie no SSID manipulation) Digi
                       ; For a Local "Fillin" Digi, you could include WIDE1-1 and leave out TraceCalls and FloodCalls
ReplaceDigiCalls       ; Replace DigiCalls with APRSCall. Omit if you want the call to be left as it is received.
MaxTraceHops=2         ; Max value of n in CALLN-n processing. If a packet is received with n greater than
MaxFloodHops=2         ; this, the value will be replaced BEFORE it is decremented.

; You can specify a fixed LAT/LONG instead of using GPS

LAT=4500.96N           ; Must be in standard APRS Format
LON=03855.04E          ; Must be in standard APRS Format

;OBJECT PATH=APRS,WIDE1-1 PORT=3,4,5,IS INTERVAL=15 TEXT=!4500.96NL03855.04E&433.775MHz LoRa APRS DIGI&IGATE
;OBJECT PATH=APRS,WIDE2-1 PORT=4,IS INTERVAL=30 TEXT=!5556.34N/03758.45EBPKT1K2/144.800,PKT300/14.1023|7.0452, https://node.r2akt.ru/

;IGATE Params. If specified you will gate RF packets and your beacons to APRS-IS

ISHost=127.0.0.1          ; APRS-IS Host Name
ISPort=14580              ; Normal port for a filtered feed
ISPasscode=24487          ; If you don`t already have a passcode I can issue you one.
ISFilter=m/100            ; Filter Command if needed

***

;IPGATEWAY
;Adapter vmbr0
;44ENCAP 172.16.14.3  ; (Must Be In DMZ)
;IPAddr 44.61.2.1
;IPNetMask 255.255.255.248
;IPPorts 5
;***

PORT
 ID=Telnet Server
 PORTNUM=1
 DRIVER=TELNET
 CONFIG
 LOGGING=1
 DisconnectOnClose=1
 CMS=1 ; Enable CMS Gateway
; CMSCALL=US1GHQ
; CMSPASS=password
 CMDPORT=63000
 HTTPPORT=9080 ; Port used for Web Management/WebMail
 TCPPORT=9010 ; Port for Telnet Access
 FBBPORT=9012 ; Not required, but allows monitoring using BPQTermTCP
 LOGINPROMPT=Callsign :
 PASSWORDPROMPT=Password :
 MAXSESSIONS=32
 USER=US1GHQ,password,US1GHQ,"",SYSOP
 USER=ANON,password
ENDPORT

PORT
 ID=AXIP
 PORTNUM=2
 DRIVER=BPQAXIP
 QUALITY=192      ;QUALITY лучше ставить всем 192, такая есть договоренность для AXUDP 
 MAXFRAME=4
 FRACK=7000
 RESPTIME=1000
 RETRIES=10
 PACLEN=236
 CONFIG
 UDP 10093        ;Listens for UDP packets on this UDP port number
 UDP 10092
 MHEARD

 MAP R2AKT-1 r2akt.ru UDP 10093 B
 MAP RN1M-5 rn1m.cats-home.net UDP 10093 B

 BROADCAST NODES
 BROADCAST ID
 AUTOADDMAP

ENDPORT

PORT
  ID=VHF_144.800MHz_AFSK_APRS_1K2
  PORTNUM=3
  TYPE=ASYNC
  PROTOCOL=KISS
;  COMPORT=/dev/ttyUSB0     ; Linux device name.      
;  SPEED=115200             ; PC to TNC Speed
  IPADDR=172.16.14.4        ; Address of PC runnning the TNC. Usually this is the same machine as BPQ, so use 127.0.0.1 but can be on another machine
  TCPPORT=10001             ; Port TNC listens on. Default for UZ7HO is 8100 and Direwolf 8001
  CHANNEL=A
  DIGIFLAG=1
  DIGIPORT=0
  FRACK=10000
  RESPTIME=3000
  RETRIES=5
  MAXFRAME=1
  PACLEN=200
  TXDELAY=400
  SLOTTIME=100
  PERSIST=64
  KISSOPTIONS=NOPARAMS
ENDPORT

PORT
  ID=UHF_433.775MHz_LoRa_APRS_0K3
  PORTNUM=4
  TYPE=ASYNC
  PROTOCOL=KISS
;  COMPORT=/dev/ttyUSB0     ; Linux device name.      
;  SPEED=115200             ; PC to TNC Speed
  IPADDR=172.16.14.5        ; Address of PC runnning the TNC. Usually this is the same machine as BPQ, so use 127.0.0.1 but can be on another machine
  TCPPORT=10001             ; Port TNC listens on. Default for UZ7HO is 8100 and Direwolf 8001
  CHANNEL=A
  DIGIFLAG=1
  DIGIPORT=0
  FRACK=10000
  RESPTIME=3000
  RETRIES=5
  MAXFRAME=1
  PACLEN=200
  TXDELAY=400
  SLOTTIME=100
  PERSIST=64
;  SETHARDWARE=440.100, -3000, SF12, CR45, 5dbm
  KISSOPTIONS=NOPARAMS
ENDPORT

PORT
  ID=UHF_432.500MHz_FSK_APRS_1.2KBPs
  PORTNUM=5
  TYPE=ASYNC
  PROTOCOL=KISS
;  COMPORT=/dev/ttyUSB0     ; Linux device name.      
;  SPEED=115200             ; PC to TNC Speed
  IPADDR=172.16.14.9        ; Address of PC runnning the TNC. Usually this is the same machine as BPQ, so use 127.0.0.1 but can be on another machine
  TCPPORT=10001             ; Port TNC listens on. Default for UZ7HO is 8100 and Direwolf 8001
  CHANNEL=A
  DIGIFLAG=1
  DIGIPORT=0
  FRACK=10000
  RESPTIME=3000
  RETRIES=5
  MAXFRAME=1
  PACLEN=200
  TXDELAY=300
  SLOTTIME=100
  PERSIST=64
;  SETHARDWARE=440.100, -3000, SF12, CR45, 5dbm
  KISSOPTIONS=NOPARAMS
ENDPORT

; здесь подправил ¤рлыки аппликаций, цифра после позывного (SSID) должна быть разной 

APPLICATION 1,BBS,,US1GHQ-8
APPLICATION 2,CHAT,,US1GHQ-4,KHECHT,255
APPLICATION 3,RMS,C 1 CMS HOST 0,US1GHQ-11,KHERMS,255

LINMAIL				; Enable BBS
;LINCHAT			: Enable chat